| pitchbook20102010
10 | GARY FISHER SERVICE INFORMATIONFender InstallationThis section explains how to install front and rear fenders on a Cronus using the accessory d
11 | GARY FISHER SERVICE INFORMATIONFinishing the installation1. Attach the foot of the rear fender.If the fender has a clip instead of a hole, remo
12 | GARY FISHER SERVICE INFORMATIONFCC Steering SystemThe Cronus uses the FCC (Fisher Control Column) with a special front hub that is mated to the
13 | GARY FISHER SERVICE INFORMATIONCrankset InstallationThese instructions explain how to install a SRAM/TruVativ/Bontrager GXP crankset (F
14 | GARY FISHER SERVICE INFORMATIONTo install the bearings1. Apply a liberal coat of grease to the contact surfaces of one bearing and the drive si
15 | GARY FISHER SERVICE INFORMATION3. Install the wave washer and with the grease facing up, slide the bearing seal onto the axle (Figure 25).4. Ap
16 | GARY FISHER SERVICE INFORMATIONThese instructions explain how to install a Shimano HollowTech (Figure 29) in a new Cronus. To
17 | GARY FISHER SERVICE INFORMATIONTo install the bearings1. Apply a liberal coat of grease to the contact surfaces of one bearing and the drive si
18 | GARY FISHER SERVICE INFORMATIONTo install the drive-side crankarmWhen handling the seals, avoid bending them. A bent seal will rub on the beari
19 | GARY FISHER SERVICE INFORMATIONTo install the non-drive side crankarm1. Apply a light coat of grease to the inside of the other bearing seal.2.
2 | GARY FISHER SERVICE INFORMATIONService InformationThe Gary Fisher Cronus is the lightest, strongest frameset we have ever made. To
20 | GARY FISHER SERVICE INFORMATIONThe Cronus uses a special bearing system that has no parts that thread into the frame. Ins
21 | GARY FISHER SERVICE INFORMATIONTo install the seal seats1. Clean all surfaces to be bonded (bottom bracket shell, seal seats) with alcohol wipe
22 | GARY FISHER SERVICE INFORMATION3. Insert the Wave washer into th
23 | GARY FISHER SERVICE INFORMATIONThese instructions and parts are for the aluminum FSA cranks only. The current “B” kit will not w
24 | GARY FISHER SERVICE INFORMATIONTo install the bearings1. Apply a liberal coat of grease to the contact surfaces of one bearing and the drive s
25 | GARY FISHER SERVICE INFORMATIONTo install the non-drive side crankarm1. Align the non-drive crank arm with the groove on the axle and slide the
26 | GARY FISHER SERVICE INFORMATIONCronus Crankset TroubleshootingThis section describes problems that occasionally occur, and possible solutions.
27 | GARY FISHER SERVICE INFORMATIONIf you notice that the crank arms rotate poorly, there are several po
3 | GARY FISHER SERVICE INFORMATIONWorking with Carbon Fiber Parts ...
4 | GARY FISHER SERVICE INFORMATIONWorking with Carbon Fiber PartsCarbon ber parts are different from metal parts, so they require different treatm
5 | GARY FISHER SERVICE INFORMATIONCutting a carbon ber steererThese instructions explain the best practices for cutting a carbon ber steerer tube
6 | GARY FISHER SERVICE INFORMATION1. Clamp the saw guide securely in the bench vise.2. Clamp the steerer in the saw guide. + Be
7 | GARY FISHER SERVICE INFORMATIONHeadset InstallationThe headset of the Cronus uses a 1.5” lower bearing and 11/8” upper bearing (Figure 5). The b
8 | GARY FISHER SERVICE INFORMATIONTo install the bearings1. Apply a light coat of grease to the inner race of the lower bearing.2. Install the bear
9 | GARY FISHER SERVICE INFORMATIONTo install the shims, bearing cover, and spacersFisher installs three 1mm shims between the centering washer and
Commentaires sur ces manuels